Guide

• How to distinguish the quality of a rubber belt

  There are several key points to distinguish the quality of a rubber belt:Material: Good V-belts are usually made of high-quality materials, such as high-quality leather or elastic fabrics. When touched, it should feel soft but sturdy, with no obvious signs of wear or breakage.Craftsmanship: Observe

  Guide July 29, 2024
• The Reason for The Slippage of The Rubber Fan Belt

  The main reasons for the slippage of the V-belt are as follows:1. Insufficient friction between the V-belt and the pulley: If there is dirt, oil or water stains on the surface of the V-belt, it will reduce the friction and cause slippage. In addition, if the operating environment temperature of the

  Guide July 26, 2024
• Reasons for The Flipping Or Detachment of The Rubber V-belt

  Analysis of the reasons for the flipping or detachment of the V-belt:1. Quality issue with the V-belt: The purchased V-belt has poor quality, insufficient tensile strength, and is prone to flipping or falling off after prolonged use.2. Improper installation: During the installation process, the tria

  Guide July 25, 2024
• What's The Reason for The Rubber Belt Always Getting Out of The Groove

  As a type of transmission belt, V-belts are widely used in various mechanical equipment. However, the rubber belt often experiences grooving, which not only affects the normal operation of the equipment, but may also cause damage to the equipment and safety accidents. So, what is the reason why the rubber belt always goes out of the groove?

  Guide July 24, 2024
• The Causes of Rubber Belt Fracture

  During use, if there is a fracture in the rubber belt, it may be caused by various factors. One possibility is that the internal structure of the rubber belt may change due to prolonged use, resulting in fracture behavior. If any negative signs are found, replace it with a new one as soon as possible. So what causes a good triangular belt to suddenly break?

  Guide March 14, 2024
• The Causes And Solutions of Cracks in Rubber Belts

  The causes and solutions of cracks in rubber beltsCause of cracks:1. The diameter and installation position of the tensioning wheel do not meet the requirements;2. Severe slipping;3. The diameter of the pulley is lower than the smaller allowable diameter limit for automotive transmission belts;

  Guide March 12, 2024
• Precautions for Replacing Rubber Belt in Cars

  Precautions for replacing the rubber v belt in a car: For car owners who are familiar with machinery, they can replace the V-belt themselves, but the most difficult point is to adjust the tension of the belt. Too loose or too tight tension is not acceptable. The appropriate tension of the belt is determined by not slipping when dragging a certain torque. Improper maintenance, or improper installation due to lack of tools, worn pulley grooves, or worn belt edges are all causes of improper tension.

  Guide March 08, 2024
• How To Determine The Tightness of The Rubber V-belt

  In modern industry, there are mainly mechanical transmission, hydraulic transmission, pneumatic transmission, and electrical transmission. Among them, mechanical transmission is the basic transmission mode, which transmits motion force and motion through meshing transmission and friction transmission, and plays an important role in it. The degree of tightness is usually determined based on usage experience, and it is good to adjust it so that the belt does not slip during transmission.

  Guide March 07, 2024
• Rubber Belt Installation And Daily Maintenance

  Before installation by the V-belt manufacturer, if the center distance between the two axes is an adjustable structure, the center distance should be shortened first. After the tape is installed, the center distance should be adjusted according to the requirements; If the center distance between the two axes is not adjustable, you can first insert a V-belt into the wheel groove, then rotate the other pulley to install the V-belt, and use the same method to install a set of V-belts.

  Guide March 05, 2024
• Why Does The Rubber Belt Generate Heat

  The heating of the V-belt may have a certain impact on its service life and transmission efficiency. Therefore, when designing and using V-belts, it is necessary to choose reasonable belt materials, maintain appropriate tension of the belt, control environmental temperature, and other measures to reduce heating.

  Guide February 29, 2024